Archives: Listings

BECKOPOX™ EH 629

BECKOPOX™ EH 629 is a Mannich base (aliphatic polyamine) primarily used as a curing agent in various applications. Here's an overview of its properties and uses:
Type:
- Mannich base (aliphatic polyamine)
Form of Delivery (F.O.D.):
- 100%
H-equivalent weight (F.O.D.):
- 70 g/mol
Special Properties and Use:
- Curing at temperatures as low as 5°C even at high humidity.
- Suitable for highly chemical-resistant coatings, adhesives, laminates, and as an accelerator for low-reactive hardeners.
Product Data:
- Dynamic Viscosity: 2500 - 4400 mPa.s (100 1/s; 23°C)
- Amine Value: 440 - 500 mg KOH/g (form of delivery)
- Iodine Colour Number: ≤ 5
- Density: Approximately 1.12 g/cm³ (20°C)
- Flash Point: > 100°C
Suggested Uses and Processing:
- Ideal for formulating solvent and chemical-resistant container linings, flooring compounds, underwater coatings for steel structures and ship decks, as well as adhesives.
- Offers good through-cure in thin films and highly extended systems, even at low curing temperatures and high humidity.
Mixing Ratio and Pot Life:
- A blend of 100 g Beckopox EP 140 and 38 g Beckopox EH 629 starts to gel at 23°C after approximately 15 - 20 minutes.
Storage:
- Stable for at least 365 days when stored at temperatures up to 25°C in original containers.
Distinguishing Features:
- Used for increasing the reactivity of curing agents.
Safety at Work and Environmental Protection:
- Adherence to local regulations and safety guidelines for handling and processing epoxy resins and hardeners is essential. Material Safety Data Sheet is available upon request.

ACURE™ 510-370 Technical Datas

ACURE™ 510-370 is a modified malonate-functional high-flow polyester resin used as a donor resin in ACURE, non-isocyanate coatings systems. Here are some key details about it:
Introduction:
- ACURE 510-370 is designed for use in premium industrial topcoats applied over epoxy primers.
- It contains 1.4 – 1.5% succinimide, a kinetic additive, which increases pot-life and open time.
Type:
- Modified malonate functional high-flow polyester resin
Form of Delivery (F.O.D.):
- 100% active
Product Data:
- Acid value, on non-volatile content: 1 maximum mg KOH/g
- Viscosity (77°F): Z5 – Z7 Gardner – Holdt
- Color: 4 maximum Gardner
- Density: 9.50 ± 0.10 lbs/gal
- Flash Point: >200°F Setaflash
- CH equivalent weight (calculated): 175
Performance Highlights:
- High order of hardness, abrasion, and mar resistance
- Solvent-free
- Succinimide dissolved in resin
Suggested Uses:
- ACURE systems are recommended for use in premium industrial topcoats applied over epoxy primers.
Storage:
- Stable for 1 year in the original sealed containers at temperatures up to 100°F.
Formulation Guidelines:
- Usage levels and other guidance related to this resin and other kinetic additives can be found in the “ACURE Paint Formulating Guide” and “The ACURE Formulator” (an MS Excel-based kinetic additive calculation tool).
Remarks:
- Contains 8 – 10% of a malonate functional reactive diluent, which is taken into account in the CH equivalent weight provided.
Precautions:
- Before using ACURE 510-370, refer to the Safety Data Sheet (SDS) for information on identified hazards, recommended personal protective equipment, and procedures.
Storage and Handling:
- Avoid exposure to high-temperature conditions, direct sunlight, ignition sources, oxidizing agents, alkalis, or acids. Store and handle in appropriate containers and wash thoroughly after handling. Keep the container tightly closed and use with adequate ventilation. See the SDS for the recommended storage temperature range.

CYMEL® 1133 Resin

CYMEL® 1133 is a highly methylated, n-butylated melamine crosslinker with a high degree of alkylation. Here are some key points about it:
Product Description:
- CYMEL® 1133 resin has a higher butoxymethyl content and higher monomer content compared to CYMEL® 1130 resin.
- Its hydrophobic nature combined with very good film appearance properties makes CYMEL® 1133 resin suitable for automotive topcoat applications and general metal finishes requiring improved durability and resistance properties.
Benefits:
- Electro deposition properties
- Film appearance properties
- Intercoat adhesion
Application Areas:
- Automotive topcoat formulations
- High solids coatings
- Anodic electrodeposition coatings
Physical Properties:
- Appearance: Clear Liquid
- Non-volatile by weight: ≥ 98%
- Viscosity (23°C): 700-1600 mPa.s
- Free formaldehyde: < 0.1%
- Color, APHA: ≤ 70
Solubility:
- Alcohols: Complete
- Esters: Complete
- Ketones: Complete
- Aromatic hydrocarbons: Complete
- Aliphatic hydrocarbons: Partial
- Water: Insoluble
Compatibility:
- Very good compatibility with acrylic resins, alkyd resins, polyester resins, and epoxy resins.
Backbone Polymer Selection:
- CYMEL® 1133 resin contains mainly methoxymethyl and n-butoxymethyl functional sites, making it highly effective for crosslinking backbone polymer resins containing hydroxyl, carboxyl, or amide functional groups, such as those found on alkyd, polyester, or acrylic resins.
Catalysis:
- Responds best to sulfonic acid catalysts, like CYCAT® 4040 catalyst or CYCAT® 600 catalyst. Generally, 0.5 to 1.0% of CYCAT® 4040 catalyst on total resin solids of the formulation is sufficient to provide good cure at normal baking schedules.
Formulation Stability:
- Stability of formulated systems containing CYMEL® 1133 resin can be enhanced by the addition of primary alcohols, amines, or a combination of these.
Storage Stability:
- Has a shelf life of 1800 days from the date of manufacture when stored at temperatures below 32°C.

SETALUX® D A 163 X

SETALUX® D A 163 X is a polyisocyanate cross-linking acrylic resin primarily used in combination with aliphatic polyisocyanates to formulate two-pack polyurethane coatings. Here are some key points about it:
Type: Polyisocyanate cross-linking Acrylic Resin
Hydroxyl Content: Approximately 2.7% on solid resin
Uses:
- Used in the formulation of lightfast and weather-stable two-pack polyurethane coatings.
- Particularly suitable for air- and force-drying top coats, anti-corrosion coatings, and top coats for steel in civil and hydraulic engineering applications.
Form Supplied: Approximately 63% in xylene
Specification:
- Non-volatile content: 63 ± 1%
- Viscosity (23°C): 4400 ± 1000 mPa·s
- Acid value (supply form): 4 ± 2 mg KOH/g
- Hydroxyl content (supply form): 1.4 to 2.0%
- Colour (Hazen): ≤ 50 APHA
- Water content: ≤ 0.1%
Other Data:
- Equivalent weight (supply form): Approximately 1030 g/eq
- Density (20°C): Approximately 0.98 g/cm³
- Flash point: Approximately 25°C
Properties/Applications:
- Used in combination with aliphatic polyisocyanates to formulate coatings with good weather stability, resistance to water, washing solutions, and chemicals.
- Stable up to approximately 150°C, but yellowing may occur at this temperature.
- Can be applied by brushing, rolling, and airless spraying.
Solubility/Thinnability:
- Can be thinned to a resin content of 30% using various solvents such as ketones, esters, ether esters, toluene, xylene, and solvent naphtha 100.
- Solutions formed must be tested for their storage stability.
Compatibility:
- Compatible with Desmodur N 75, N 3390, Z 4470, and L, as well as SETATHANE® D 1150, but combinations must be tested for compatibility.
- Also compatible with various types of nitrocellulose chips and certain vinyl copolymers, but compatibility testing is advisable.
Storage:
- Should be stored in originally sealed containers at temperatures not exceeding 30°C.
Shelf Life:
- Standard shelf life is 730 days from the date of manufacturing, but may be extended upon re-testing by QC.
This product data sheet provides essential information for the formulation and application of SETALUX® D A 163 X. Additional safety-related information can be found in the corresponding Safety Data Sheet.

EBECRYL® 1271

EBECRYL® 1271 is a difunctional aliphatic urethane diacrylate primarily used in the formulation of ultraviolet light (UV) and electron beam (EB) energy curable coatings. Here are some key points about it:
Introduction:
- EBECRYL® 1271 does not contain intentionally added organic tin compounds, heavy metals, hydroquinone (HQ), or methyl ether of hydroquinone (MEHQ). However, it may contain quinones present in raw materials.
- Cured films of EBECRYL® 1271 by UV or EB exhibit good flexibility, adhesion, abrasion resistance, exterior durability, and resistance to yellowing.
Performance Highlights:
- EBECRYL® 1271 is characterized by:
  - No intentionally added tin, heavy metals, or quinones
  - Light color
- UV/EB cured products containing EBECRYL® 1271 offer:
  - Regulation-friendly attributes for tin, heavy metals, and quinones
  - Good flexibility
  - Good adhesion
  - Non-yellowing
  - Exterior durability
  - Abrasion resistance
- Actual properties depend on the selection of other formulation components such as reactive diluents, additives, and photoinitiators.
Suggested Applications:
- Formulated UV/EB curable products containing EBECRYL® 1271 may be applied via various methods including brush, roller, direct or reverse roll, offset gravure, metering rod, slot die, knife over roll, air knife, curtain, immersion, and spin coating, as well as screen printing.
- Recommended for applications requiring compliance with regulations for tin, heavy metals, and quinone content.
- Suitable for coatings for wood and plastic requiring good exterior durability, coatings for rigid and flexible plastics, and metal coatings.
Typical Values:
- Appearance: Clear liquid
- Color: Maximum 75 (Apha scale)
Typical Physical Properties:
- Density: 1.04 g/cm³ at 25°C
- Functionality: Theoretical 2
- HQ/MEHQ Content: 2/5 ppm
- Viscosity: 4550 mPa.s at 60°C
Typical Cured Properties:
- Tensile Strength: 13.9 MPa
- Elongation at Break: 54%
- Young’s Modulus: 29.1 MPa
- Glass Transition Temperature: 19°C
Viscosity Reduction:
- Reactive diluents such as 1,6-hexanediol diacrylate (HDDA), isobornyl acrylate (IBOA), trimethylolpropane triacrylate (TMPTA), and tripropylene glycol diacrylate (TPGDA) can reduce the viscosity of EBECRYL® 1271. This reduction can influence properties like hardness and flexibility.
Precautions:
- Refer to the Safety Data Sheet (SDS) for identified hazards, recommended personal protective equipment, and procedures.
- Store and handle carefully to avoid exposure to high temperatures, direct sunlight, ignition sources, oxidizing agents, alkalis, or acids.
- Storage and handling should be in appropriate containers and conditions to prevent uncontrollable polymerization.
- Use with adequate ventilation and wash thoroughly after handling.
Overall, EBECRYL® 1271 offers a range of benefits and is suitable for various coating applications, particularly those requiring compliance with specific regulations and high-performance characteristics.

EBECRYL® 4683

EBECRYL® 4683 is an aliphatic urethane acrylate primarily used in the formulation of ultraviolet light (UV) and electron beam (EB) energy curable coatings. Here are some key points about it:
Introduction:
- EBECRYL® 4683 is an aliphatic urethane acrylate diluted 35% by weight with isobornyl acrylate (IBOA).
- It's designed for UV and EB energy curable coatings, producing hard, tough coatings suitable for protective coating on metal and other rigid substrates.
Performance Highlights:
- UV/EB cured coatings based on EBECRYL® 4683 offer:
  - Good chemical resistance
  - Very good mechanical properties
  - High abrasion resistance
  - Scratch resistance
  - Low yellowing
- Actual properties depend on the selection of other formulation components such as reactive diluents, additives, and photoinitiators.
Suggested Applications:
- Formulation of UV/EB energy curable coatings for roller coating, spraying, and curtain coating on metal and other rigid substrates.
Formulating:
- Coatings can be adjusted for viscosity with additional IBOA or other reactive diluents such as dipropylene glycol diacrylate (DPGDA), hexanediol diacrylate (HDDA), trimethylolpropane triacrylate (TMPTA), or solvents like butyl acetate.
- Compatible with most acrylate monomers and oligomers, but compatibility should be tested in each case.
- UV curing requires the addition of standard commercial photoinitiators. EB curing requires a low oxygen atmosphere to avoid surface inhibition.
Typical Physical Properties:
- Color: <100 (Pt-Co scale)
- Density: 1.10 g/cm³ at 20°C
- Flash point: 94°C
- NCO content: <0.2%
- Viscosity: ~50000 mPa.s at 23°C
Typical Cured Properties:
- Tensile strength: 69 MPa (10000 psi)
- Elongation at break: 6%
- Young’s modulus: 2000 MPa (290000 psi)
- Glass transition temperature: 90°C
Precautions:
- Refer to the Safety Data Sheet (SDS) for identified hazards, recommended personal protective equipment, and procedures.
- Avoid exposing the product to high temperatures, direct sunlight, ignition sources, oxidizing agents, alkalies, or acids.
- Store and handle in appropriate containers and conditions to prevent uncontrollable polymerization.
Storage and Handling:
- Store in stainless steel, amber glass, amber polyethylene, or baked phenolic lined containers.
- Avoid storing under an oxygen-free atmosphere.
- Use with adequate ventilation and wash thoroughly after handling.
- See SDS for recommended storage temperature range.

allnex PC 2544 Defoamer

PC-2544™ Defoamer is a solution primarily used to improve the stability performance of defoamers in formulated Group I and Group II lubricants. Here are some key points about it:
Introduction:
- PC-2544 Defoamer is a 40% solution of an acrylic polymer in a hydrocarbon solvent.
- It's designed to enhance defoamer stability in lubricants and is suggested for specialty applications requiring efficient high-temperature performance.
- Typical use levels range from 50 - 500 ppm (20 - 200 ppm active polymer), with the optimum level depending on the nature of the oil.
Available Regions:
- Asia-Pacific, Europe/Africa, North America, South America.
Physical Properties:
- Appearance: Clear, colorless to light yellow liquid.
- Refractive Index (nD25 @ 25°C): 1.4400 - 1.4420.
- Non-Volatiles (%): 38 - 42% (2 hrs. @ 105°C).
- Viscosity (SUS @ 100°F): 150 - 400.
- Specific Gravity @ 77°F (25°C): 0.84 - 0.86.
- Color (APHA): 150 max.
- Flash Point: > 149°F (> 65°C).
- Brookfield Viscosity (cps @ 77°F): 40 - 150.
- Solvent: Hydrocarbon.
Useful Information:
- It's important to conduct a concentration profile on each oil to determine the optimum level of PC-2544 Defoamer.
- The product is listed on all major country inventories (see MSDS).
Shelf-Life:
- At temperatures up to 35°C, storage stability packed in original containers amounts to at least 1460 days.

ADDITOL® XL 203

ADDITOL® XL 203 is a silicone-containing cationic antifloating, wetting, and dispersing agent primarily used in paint systems to prevent the floating of titanium dioxide and enhance pigment dispersion. Here's a breakdown of its key features, specifications, and suggested uses:
Type:
Silicone-containing cationic antifloating, wetting, and dispersing agent.
Form of Delivery (f.o.d.):
Active substance approx. 40%.
Product Data:
- Dynamic Viscosity (100 1/s; 23°C): 30 - 120 mPa.s
- Iodine Colour Number: <= 20
- Non-Volatile Matter (1 h; 125°C; 1 g): 38.5 - 41.5%
- Density (20°C): approx. 0.98 g/cm³
- Flash Point: approx. 63°C
- Appearance: brown, clear liquid
Special Properties:
- High pigment loading without an increase in viscosity.
- Reduction of dispersing time.
- Enhances gloss and leveling.
- Suitable for air drying and stoving solvent-borne paints and particularly for water-dilutable paint systems.
Suggested Uses:
- Prevents the floating of titanium dioxide in conjunction with organic or inorganic colored pigments.
- Enhances gloss and leveling of paint films.
- Allows for increased pigment loading without rises in viscosity.
- Recommended dosage range: 0.1 to 1.5% on total paint. Level on pigments: inorganic pigments (0.5 - 2.5%), organic pigments (1.5 - 5%).
Processing:
- Should be milled together with the pigments to obtain the full effect.
Storage:
- Storage stability packed in original containers at temperatures up to 25°C is at least 730 days.
Distinguishing Features:
- Unlike Additol XL 204, Additol XL 203 is a cationic-active antifloating agent suitable for solvent- and waterborne paint systems. It is not recommended for acid-curing paints.
Compatibility:
- Should not be used in conjunction with certain anionic products to prevent phase separation. Compatibility should be determined by experiments. Can be combined with cationic and non-ionic products.
In summary, ADDITOL® XL 203 serves as an effective antifloating and dispersing agent in various paint systems, contributing to improved pigment dispersion, gloss, and leveling while maintaining stability and compatibility with other components.

SETALUX® 1910 BA-75

SETALUX® 1910 BA-75 is an acrylic polyol dispersion primarily used in two-component clearcoats and solid color topcoats for vehicle refinish and industrial applications. Here's a breakdown of its key features, specifications, and application guidelines:
Type:
An acrylic polyol with 3.6% OH (calculated on non-volatiles), belonging to the ECOWISE™ CHOICE product range for selected applications.
Solvent Composition:
Butyl acetate
Specifications:
- Non-Volatiles: 74 - 76%
- Viscosity (23°C, 100s^-1):
  - (at 74% NV): 3.9 - 6.6 Pa.s
  - (at 75% NV): 5.0 - 8.5 Pa.s
  - (at 76% NV): 6.4 - 11 Pa.s
- Acid value (as such): 4.9 - 8.7 mg KOH/g
- Color APHA (Lico): max. 35 APHA
Typical Properties:
- Hydroxyl value: approx. 120 mg KOH/g
- Density: 1.04 kg/dm³
- Flash point: 23.5°C
Technical Features:
- Provides VOC compliant coatings (< 420 g/l) at low spray viscosity
- Offers high build and gloss
- Good hardness build-up
- Exhibits good mechanical properties and outdoor durability
Application:
- Suitable for two-component clearcoats and solid color topcoats for vehicle refinish and industrial topcoats.
Storage Conditions:
- Keep container tightly closed and dry in a cool, well-ventilated place.
- Keep away from heat, sparks, flame, and other sources of ignition.
Shelf Life:
- Standard shelf life is 720 days from the date of manufacturing. Shelf life may be extended based upon retesting by allnex Quality Control.
Compatibility:
- Compatible with various acrylic and polyester polyols as well as other materials listed in the compatibility chart.
Dilutability:
- Dilutable with certain aromatic solvents, esters, ketones, and others as listed in the datasheet.
In summary, SETALUX® 1910 BA-75 offers excellent properties for producing clearcoats and topcoats with high gloss, durability, and compliance with VOC regulations. It is designed for use in automotive refinish and industrial applications, providing versatility and performance. Proper storage and handling are essential to maintain its effectiveness and shelf life.

SETAQUA® 6803

SETAQUA® 6803 is an acrylic copolymer dispersion primarily used as a base coat for metallic and solid color waterborne automotive coatings. Here's a breakdown of its key features, specifications, and application guidelines:
Solvent Composition:
- Demineralized water
Specifications:
- Non-Volatiles: 22 - 26%
- Viscosity flowcurve (23°C, 500 s^-1): 0.15 - 0.45 Pa.s
- Viscosity flowcurve (23°C, 1 s^-1): 20 - 45 Pa.s
- Acid value (as such): 5.5 - 7.5 mg KOH/g
Typical Properties:
- Density: approximately 1.03 kg/dm³
Technical Features:
- Pseudo-plastic after neutralization
- Good aluminum orientation
- Good atomization
- Insoluble in organic solvents
- Excellent stability
Application:
- Used in metallic and solid color waterborne base coats for the automotive OEM industry
Storage Conditions:
- Should not be stored at temperatures below 0°C or above 35°C
- Avoid exposure to direct sunlight and prevent freezing
Shelf Life:
- Standard shelf life is 180 days from the date of manufacturing, but it may be extended based upon retesting by allnex Quality Control.
In summary, SETAQUA® 6803 offers excellent stability and is specifically designed for automotive coatings, providing desirable properties for base coats in the OEM industry. Proper storage and handling are essential to maintain its effectiveness and shelf life.